Search Results

As new advanced-technology vehicles are becoming more mainstream, analysts are studying their potential impact on petroleum use, carbon emissions, and smog emissions. Determining the potential impacts of widespread adoption requires testing and careful analysis. PHEVs possess unique operational characteristics that require evaluation in terms of actual in-use driving habits. SAE J2841, “Utility Factor Definitions for Plug-In Hybrid Electric Vehicles Using 2001 U.S. DOT National Household Travel Survey Data,” published by SAE in 2009 with a revision in 2010, is a guide to using DOT's National Household Travel Survey (NHTS) data to estimate the relative split between driving in charge-depleting (CD) mode and charge-sustaining (CS) mode for a particular PHEV with a given CD range. Without this method, direct comparisons of the merits of various vehicle designs (e.g., efficiency and battery size) cannot be made among PHEVs, or between PHEVs and other technologies.

This paper outlines the development and progress of implementing the SAE J2931, J2847/2 and J1772 communication standards to accomplish off-board DC charging. Communication between the off-board DC Electric Vehicle Supply Equipment (EVSE) and Plug-in Electric Vehicle (PEV) occurs on the pilot wire of the SAE J1772 connector via HomePlug Green PHY power line communication (PLC). An Electric Vehicle Communication Controller (EVCC) was developed to interface with the PEV's Battery Energy Control Module (BECM). A Supply Equipment Communication Controller (SECC) was also developed to interface with the DC EVSE's Power Control Module (PCM). Firmware was developed to implement the SAE J2931/1 communication stack, which is harmonized with the ISO/IEC DIS 15118-2 and DIN 70121 standards for DC charging communication.

This paper presents the vehicle model development and validation process for the Ford Focus battery electric vehicles (BEVs) using Autonomie and test results from Advanced Powertrain Research Facility in Argonne National Laboratory. The parameters or characteristic values for the important components such as the electric machine and battery pack system are estimated through analyzing the test data of the multi cycle test (MCT) procedure under the standard ambient condition. A novel process was used to import vehicle test data into Autonomie. Through this process, a complete vehicle model of the Ford Focus BEV is developed and validated under ambient temperature for different drive cycles (UDDS, HWFET, US06 and Steady-State). The simulation results of the developed vehicle model show coincident results with the test data within 0.5% ∼ 4% discrepancies for electrical consumption.

To restrain the phenomenal increase in oil consumption in China, the Chinese government called for measures to reduce oil consumption of the road transportation sector through adopting vehicle fuel consumption standards. This paper describes the development of China's first set of fuel consumption standards for light-duty passenger vehicles. The adopted standards cover M1 class vehicles, which, according to European definition (and adopted by China), include passenger cars, minivans, and sports utility vehicles (SUVs). In particular, we present the goal, technical background, structure, and values of the adopted standards. We also present their potential effect on oil use reduction. The standards are set in liters of fuel consumption per 100 km for individual vehicle weight categories. The standards are maximum fuel consumption values for given vehicle weight categories.

In an earlier paper, the authors described how Model-Based System Engineering could be utilized to provide a virtual Hardware-in-the-Loop simulation capability, which creates a framework for the development of virtual ECU software by providing a platform upon which embedded control algorithms may be developed, tested, updated, and validated. The development of virtual ECU software is increasingly valuable in automotive control system engineering because vehicle systems are becoming more complex and tightly integrated, which requires that interactions between subsystems be evaluated during the design process. Variational analysis and robustness studies are also important and become more difficult to perform with real hardware as system complexity increases. The methodology described in this paper permits algorithm development to be performed prior to the availability of vehicle and control system hardware by providing what is essentially a virtual integration vehicle.

In order to determine the factors that affect fuel economy quantitatively, the power flows through the major powertrain components were measured during operation over transient cycles. The fuel consumption rate and torque and speed of the engine output and axle shafts were measured to assess the power flows in a vehicle with a CVT. The measured power flows were converted to energy loss for each component to get the efficiency. Tests were done at Phase 1 and Phase 3 of the FTP and for two different CVT shift modes. The measured energy distributions were compared with those from the ADVISOR simulation and to results from the PNGV study. For both the Hot 505 and the Cold 505, and for both shift modes, the major powertrain loss occurs in the engine, including or excluding standby losses. However, the efficiency of the drivetrain/transmission is important because it influences the efficiency of the engine.

EcoCAR 2: Plugging in to the Future (EcoCAR) is North America's premier collegiate automotive engineering competition, challenging students with systems-level advanced powertrain design and integration. The three-year Advanced Vehicle Technology Competition (AVTC) series is organized by Argonne National Laboratory, headline sponsored by the U. S. Department of Energy (DOE) and General Motors (GM), and sponsored by more than 30 industry and government leaders. Fifteen university teams from across North America are challenged to reduce the environmental impact of a 2013 Chevrolet Malibu by redesigning the vehicle powertrain without compromising performance, safety, or consumer acceptability. During the three-year program, EcoCAR teams follow a real-world Vehicle Development Process (VDP) modeled after GM's own VDP. The EcoCAR 2 VDP serves as a roadmap for the engineering process of designing, building and refining advanced technology vehicles.

Diesel injections with various nozzle geometries were tested to investigate the spray characteristics by optical imaging techniques. Sac-nozzle and VCO nozzle with single guided needle coupled with rotary-type mechanical pump were compared in terms of macroscopic spray development and microscopic behavior. These nozzles incorporated with common-rail system were tested to see the effect of high pressure injection. Detailed investigation into spray characteristics from the holes of VCO nozzles, mostly with double guided needle, was performed. A variety of injection hole geometries were tested and compared to give tips on better injector design. Different hole sizes and taper ratio, represented as K factor, were studied through comprehensive spray imaging techniques. Global characteristics of a diesel spray, such as spray penetration, spray angle and its pattern, were observed from macroscopic images.

The internal structure of Diesel fuel injectors is known to have a significant impact on the nozzle flow and the resulting spray emerging from each hole. In this paper the three-dimensional transient flow structures inside a Diesel injector is studied under nominal (in-axis) and realistic (including off-axis lateral motion) operating conditions of the needle. Numerical simulations are performed in the commercial CFD code CONVERGE, using a two-phase flow representation based on a mixture model with Volume of Fluid (VOF) method. Moving boundaries are easily handled in the code, which uses a cut-cell Cartesian method for grid generation at run time. First, a grid sensitivity study has been performed and mesh requirements are discussed. Then the results of moving needle calculations are discussed. Realistic radial perturbations (wobbles) of the needle motion have been applied to analyze their impact on the nozzle flow characteristics.

Exhaust gas recirculation (EGR) is a commonly used technique for the reduction of Nitrogen oxide (NOx) emissions from internal combustion engines. However, it is generally known that the use of EGR will cause an increase in emissions of particulate matter (PM). The effects of EGR operating mode on particulate morphology were investigated for a 1.7-liter light-duty diesel engine. This engine was equipped with a turbocharged and inter-cooled air induction system, a common-rail direct fuel injection system, and an EGR system. A rapid prototyping electronic control system (RPECS) was developed to operate this engine at various EGR rates under different conditions (i.e. constant boost pressure, constant oxygen-to-fuel ratio (OFR)). A unique thermophoretic sampling system was employed to collect particulates directly from exhaust manifold after exhaust valves.

The detailed morphological properties of diesel particulate matter were analyzed along the exhaust system at various engine operating conditions (in a range of 1000 - 2500 rpm and 10 - 75 % loads of maximum torques). A 1.7-L turbocharged light-duty diesel engine was powered with California low-sulfur diesel fuel injected by a common-rail injection system, of which particulate emissions were controlled by an exhaust gas recirculation (EGR) system and two oxidation catalysts. A unique thermophoretic sampling system first developed for internal combustion engine research, a high-resolution transmission electron microscope (TEM), and a customized image processing/data acquisition system were key instruments that were used for the collection of particulate matter, subsequent imaging of particle morphology, and detailed analysis of particle dimensions and fractal geometry, respectively.

SunDiesel™ is an alternative bio-fuel derived from wood chips that has certain properties that are superior to those of conventional diesel (D2). In this investigation, 100% SunDiesel was tested in a Mercedes A-Class (model year 1999), 1.7L, turbocharged, direct-injection diesel engine (EURO II) equipped with a common-rail injection system. By using an endoscope system, Argonne researchers collected in-cylinder visualization data to compare the engine combustion characteristics of the SunDiesel with those of D2. Measurements were made at one engine speed and load condition (2,500 rpm, 50% load) and four start-of-injection (SOI) points, because of a limited source of SunDiesel fuel. Significant differences in soot concentration, as measured by two-color optical pyrometry, were observed. The optical and cylinder pressure data clearly show significant differences in combustion duration and ignition delay between the two fuels.

This research investigates the energy savings achieved through eco-driving controls in connected and automated vehicles (CAVs), with a specific focus on the influence of powertrain characteristics. Eco-driving strategies have emerged as a promising approach to enhance efficiency and reduce environmental impact in CAVs. However, uncertainty remains about how the optimal strategy developed for a specific CAV applies to CAVs with different powertrain technologies, particularly concerning energy aspects. To address this gap, on-track demonstrations were conducted using a Chrysler Pacifica CAV equipped with an internal combustion engine (ICE), advanced sensors, and vehicle-to-infrastructure (V2I) communication systems, compared with another CAV, a previously studied Chevrolet Bolt electric vehicle (EV) equipped with an electric motor and battery.

Hybrid electric vehicles (HEVs) may have key fuel economy and emissions advantages over current conventional vehicles, but they have drawbacks such as frequent engine starts that can slow down market penetration of HEVs. First, the hydrocarbon emissions due to the numerous engine starts would make newly developed HEV powertrains even more demanding on the emission control system. Second, frequent starts may make the engine deteriorate quickly. This study is an attempt to gain a better understanding of the engine start characteristics of two limited-production HEVs (Toyota Prius and Honda Insight). Using fast-response (5 ms) hydrocarbon and NO (nitric oxide) analyzers, the transient emissions were measured in the engine exhaust ports during cold and hot engine starts. On the basis of the experimental findings, several recommendations were made to improve performance and emissions of future HEVs.

Plug-in hybrid electric vehicles (PHEVs) have been identified as an effective technology to displace petroleum by drawing significant off- board energy from the electrical grid. A plug-in vehicle uses a large capacity battery to operate in an electric-only or a blended mode of operation over a large SOC window (60-80% of total operational SOC) for maximum petroleum displacement. Some advanced chemistry batteries have show that low ambient (battery) temperature has a significant impact on the performance of a PHEV battery. This paper quantifies the impact of low ambient (battery) temperature on a PHEV electric range using Hardware-in-the-Loop (HIL) methods. Combining ultra capacitors with batteries could provide a solution to overcome PHEV battery performance limitations at low temperatures.

The physical and morphological properties of the particulate matter emitted from a 1.7-liter light-duty diesel engine were characterized by observing its evolution in size and fractal geometry along the exhaust system. A common-rail direct-injection diesel engine, the exhaust system of which was equipped with a turbocharger, EGR, and two oxidation catalysts, was powered with a California low-sulfur diesel fuel at various engine-operating conditions. A unique thermophoretic sampling system, a high-resolution transmission electron microscope (TEM), and customized image processing/data acquisition systems were key instruments that were used for the collection of particulate matter, subsequent imaging of particle morphology, and detailed analysis of particle dimensions and fractal geometry, respectively. The measurements were carried out at four different positions along the exhaust pipe.

Automated driving functionalities delivered through Advanced Driver Assistance System (ADAS) have been adopted more and more frequently in consumer vehicles. The development and implementation of such functionalities pose new challenges in safety and functional testing and the associated validations, due primarily to their high demands on facility and infrastructure. This paper presents a rather unique Vehicle-in-the-Loop (VIL) test setup and methodology compared those previously reported, by combining the advantages of the hardware-in-the-loop (HIL) and traditional chassis dynamometer test cell in place of on-road testing, with a multi-agent real-time simulator for the rest of test environment.

Stringent emission standards are driving the development of diesel-fuel injection concepts to mitigate in-cylinder formation of particulates. While research has demonstrated significant reduction in particulate formation using micro-orifice technology, implementation requires development of industrial processes to fabricate micro-orifices with diameters as low as 50 μm and with large length-to-diameter ratios. This paper reviews the different processes being pursued to fabricate micro-orifices and the advanced techniques applied to characterize the performance of micro-orifices. The latter include the use of phase-contrast x-ray imaging of electroless nickel-plated micro-orifices and laser imaging of fuel sprays at elevated pressures. The experimental results demonstrate an industrially viable process to create small uniform orifices that improve spray formation for fuel injection.

Detailed diesel particulates morphology, nanostructures, fractal geometry, and nitrogen oxides (NOx) emissions were analyzed for five different test fuels in a 1.7-L, common-rail direct-injection diesel engine. The accurately formulated fuels permit the effects of sulfur, paraffins, aromatics, and naphthene concentrations to be determined. A novel thermophoretic sampling technique was used to collect particulates immediately after the exhaust valves. The morphology and nanostructures of particulate samples were examined, imaged with a high-resolution transmission electron microscope (HRTEM), and quantitatively analyzed with customized digital image processing/data acquisition systems. The results show that the particle sizes and the total mass of particulate matter (PM) emissions correlate most strongly with the fuels' aromatics and sulfur content.

The Advanced Battery Readiness Ad Hoc Working Group, a government- industry forum sponsored by the United States Department of Energy, is charged with assessing environmental and safety issues associated with advanced batteries for electric and hybrid electric vehicles. Electric and hybrid electric vehicles require sophisticated advanced battery storage systems. Frequently, toxic, reactive, and flammable substances are used in the energy storage systems. Often, the substances have safety, recycling, and shipping implications with respect to U.S. Environmental Protection Agency and Department of Transportation regulations. To facilitate commercialization, reg-ulations must either be modified or newly developed. Government-industry coordination has expedited needed regulatory changes, and promoted other partnerships to achieve environmental and safety solutions.